SIGN-UPPart Number Guide
Please note that the values in the tables below are typical. Please refer to respective data sheet for full details.
VHF Narrow Band Transmitter, Receiver and Transceiver
TX1 Transmitter and RX1 receiver are Narrowband VHF modules in SIL foot print and available in 173.225MHz and 173.250MHz as standard. Other frequencies are also available from 151.300MHz to 173.250MHz.
The BiM1 is a narrow band VHF transceiver module and also available as separate BiM1T transmitter and BiM1R receiver, which can be used as dual-in-line equivalents of TX1 and RX1 respectively. BiM1 is available in 151.300MHz, 173.225MHz and 173.250MHz as standard.
The new 500mW BiM1H transceiver opeartes on the 169MHz EU licence exempt band. (BiM1H data sheet).
Other frequencies are also available from 120MHz to 180MHz.
Non standard frequencies are subject to minimum order quantity and long lead time.
|
Frequency
(MHz) |
Supply
(Volts) |
Data rate
(kbit/s) |
Performance
(dBm,50W) |
Type
Approvals |
||
| TX Power | RX Sensitivity | |||||
| TX1-173.225-10* | 173.225 | 2.2 to 12 | 10 | +10 | - | EN 300 220-3 |
| TX1-173.250-10 | 173.250 | 2.2 to 12 | 10 | +10 | - | EN 300 220-3 |
| ENT1-169.40625-3 | 169.40625 | 5.0 | 3 | +20 | - | EN 300 220-3 |
| TX1H-151.300-10 | 151.300 | 3.8 to 15 | 10 | +20 | - | Note 3 |
| HX1-169.4125-3 | 169.4125 | 5.0 | 3 | +27 | - | EN 300 220-3 |
| RX1-173.225-10* | 173.225 | 2.7 to 12 | 10 | - | -116 | EN 300 220-3 |
| RX1-173.250-10 | 173.250 | 2.7 to 12 | 10 | - | -116 | EN 300 220-3 |
| NRX1-173.225-10* | 173.225 | 2.9 to 15 | 10 | - | -120 | Note 3 |
| NRX1-173.250-10 | 173.250 | 2.9 to 15 | 10 | - | -120 | Note 3 |
| NRX1-151.300-10 | 151.300 | 2.9 to 15 | 10 | - | -120 | Note 3 |
| Low current (1mA) receiver | ||||||
| RX1L-173.225-10* | 173.225 | 3.1-9 | 10 | - | -120 | EN 300 220-3 |
| RX1L-151.300-10 | 151.300 | 3.1-9 | 10 | - | -120 | |
| BiM1T-151.300-10 | 151.300 | 3.8 to 15 | 10 | +20 | Note 3 | |
| BiM1R-151.300-10 | 151.300 | 3.8 to 15 | 10 | - | -120 | Note 3 |
| BiM1T-173.250-10 | 173.250 | 3.8 to 15 | 10 | +10 | EN 300 220-3 | |
| BiM1R-173.250-10 | 173.250 | 3.8 to 15 | 10 | - | -120 | EN 300 220-3 |
| CVR1-173.225-10* | 173.225 | 3.0 | 10 | - | -120 | EN 300 220-3 |
| CVR1-173.250-10 | 173.250 | 3.0 | 10 | - | -120 | EN 300 220-3 |
| CVR1-151.300-10 | 151.300 | 3.0 | 10 | - | -120 | Note 3 |
| BiM1-151.300-10 | 151.300 | 3.8 to 15 | 10 | +20 | -120 | Note 3 |
| BiM1-151.300-10-LP | 151.300 | 3.0 to 15 | 10 | +10 | -120 | Note 3 |
| BiM1-173.225-10* | 173.225 | 3.0 to 15 | 10 | +10 | -120 | EN 300 220-3 |
| BiM1-173.250-10 | 173.250 | 3.0 to 15 | 10 | +10 | -120 | EN 300 220-3 |
| BiM1-173.250-10-HP | 173.250 | 3.8 to 15 | 10 | +20 | -120 | EN 300 220-3 |
| BiM1H-169.4125-3 | 169.4125 | 5.0 | 3 | +27 | -120 | Note 3 |
*173.225MHz UK VHF allocation: alarm systems and security use only
UHF Wide Band Transmitter and Receiver - 433MHz band
TX2 and RX2 are UHF Wide Band FM transmitter and receiver modules, which combine full screening with extensive internal filtering to ensure EMC compliance. TX2& RX2 modules are CE marked by independent notified body by complying to radio standard EN 300-220-3 and EMC standard EN 301 489-3.
The new TX2A/TX2H and RX2A are crystal based PLL controlled FM transmitter and receiver modules. RX2A has Received Signal Strength Indicator output instead of CD on the standard RX2.
The new TX2S is a crystal-controlled miniature transmitters measuring only 20x10x2 mm hence suitable for small RF devices such as remote control key fobs and RF tags.
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Type Approval | |
| TX Power | RX Sensitivity | |||||
| TX2S-433-40-3V | 433.92 | 2.2 to 4 | 40 | + 4 | - | EN 300-220-3 |
| TX2S-434-40-5V | 434.42 | 2.2 to 4 | 40 | + 4 | - | EN 300-220-3 |
| TX2-418-40-3V | 418 | 2.2 to 4 | 40 | -3 | - |
Note 3
|
| TX2-418-40-5V | 418 | 4.0 to 6.0 | 40 | 0 | - | Note 3 |
| TX2-433-40-3V | 433.92 | 2.2 to 4 | 40 | + 4 | - | EN 300-220-3 |
| TX2-433-40-5V | 433.92 | 4.0 to 6.0 | 10 | +10 | - | EN 300-220-3 |
| TX2-433-160-5V | 433.92 | 4.0 to 6.0 | 160 | +10 | - | EN 300-220-3 |
| TX2-433-160-3V | 433.92 | 2.2 to 4 | 160 | +4 | - | EN 300-220-3 |
| RX2-418-14-3V | 418 | 3.0 to 4.0 | 14 | - | -107 | N/A |
| RX2-418-14-5V | 418 | 4.0 to 6.0 | 14 | - | -107 | N/A |
| RX2-418-40-3V | 418 | 3.0 to 4.0 | 40 | - | -100 | N/A |
| RX2-418-40-5V | 418 | 4.0 to 6.0 | 40 | - | -100 | N/A |
| RX2-433-14-3V | 433.92 | 3.0 to 4.0 | 14 | - | -107 | EN 300-220-3 |
| RX2-433-14-5V | 433.92 | 3.0 to 6.0 | 14 | - | -107 | EN 300-220-3 |
| RX2-433-40-3V | 433.92 | 3.0 to 4.0 | 40 | - | -100 | EN 300-220-3 |
| RX2-422-40-5V | 433.92 | 4.0 to 6.0 | 40 | - | -100 | EN 300-220-3 |
| RX2-433-160-5V | 433.92 | 4.06 to 6.0 | 160 | - | -90 | EN 300-220-3 |
| RX2-433-160-3V | 433.92 | 3.0 to 4.0 | 160 | - | -90 | EN 300-220-3 |
| TX2A-433-64 | 433.92 | 2.2 to 16 | 64 | +10 | - | EN 300-220-3 |
| TX2A-433-64-5V | 433.92 | 4.0 to 6.0 | 64 | +10 | - | EN 300-220-3 |
| TX2A-433-64-3V | 433.92 | 3.0 to 4.0 | 64 | +10 | - | EN 300-220-3 |
| TX2H-433-64-3V | 433.92 | 2.5 to 3.5 | 64 | +14 | - | Note 3 |
| TX2H-433-64-5V | 433.92 | 4.5 to 5.5 | 64 | +14 | - | Note 3 |
| TX2EH-433-64 | 433.92 | 4.5 to 5.5 | 64 | +20 | - | Note 3 |
| RX2A-433-10 | 433.92 | 2.7 to 16 | 10 | - | -108 | EN 300-220-3 |
| RX2A-433-64 | 433.92 | 2.7 to 16 | 64 | - | -101 | EN 300-220-3 |
| RX2A-434-10 | 434.42 | 2.7 to 16 | 10 | - | -108 | EN 300-220-3 |
| RX2A-434-64 | 434.42 | 2.7 to 16 | 64 | - | -101 | EN 300-220-3 |
| RX2G-433-15 | 433.92 | 5.0 | 15 | - | -108 | EN 300-220-3 |
| RX2G-433-64 | 433.92 | 5.0 | 64 | - | -102 | EN 300-220-3 |
| RX2G-434-15 | 434.42 | 5.0 | 15 | - | -108 | EN 300-220-3 |
| RX2G-434-64 | 434.42 | 5.0 | 64 | - | -102 | EN 300-220-3 |
UHF Narrow Band Transmitter and Receiver
The NTX2 and NRX2 are narrow band transmitter and receiver modules and offer a low power, reliable data link in a Radiometrix SIL standard pin out and foot print. This makes the NTX2/NRX2 pair ideally suited to those low power applications where existing single frequency wideband UHF modules have insufficient range. (NTX2/NRX2)
|
Module
|
Frequency
(MHz) |
Supply
(Volts) |
Data rate
(kbit/s) |
Performance
(dBm,50W) |
Type
Approvals |
|
| TX Power | RX Sensitivity | |||||
| NTX2-434.075-10 | 434.075 | 2.9 to 15 | 10 | +10 | - | EN 300 220-3 |
| NTX2-434.65-10 | 434.65 | 2.9 to 15 | 10 | +10 | - | EN 300 220-3 |
| NTX2-434.65-10 | 434.65 | 3.6 to 15 | 10 | +14 | - | Note 3 |
| NTX2-458.700-10 | 458.700 | 2.9 to 15 | 10 | +10 | - | EN 300 220-3 |
| NRX2-434.075-10 | 434.075 | 2.9 to 15 | 10 | - | -112 | EN 300 220-3 |
| NRX2-434.65-10 | 434.65 | 2.9 to 15 | 10 | - | -112 | EN 300 220-3 |
| NRX2-458.700-10 | 458.700 | 2.9 to 15 | 10 | - | -112 | EN 300 220-3 |
UHF Wide Band Transmitter and Receiver - 868/915 MHz band
TX3A transmitters and RX3 receivers are UHF Wide Band FM modules and they operate on European and North American ISM bands. The European version is CE marked by independent notified body by complying to radio standard EN 300-220-3 and EMC standard EN 301 489-3. (TX3A/RX3A)
The new TX3B radio transmitter module is an enhanced high power replacement for the European version TX3A-869-64 transmitter. TX3H is high power transmitter operating in the 869.5MHz European licence exempt frequency. (TX3B datasheet); (TX3H datasheet)
The new TX3S is a crystal-controlled miniature transmitters measuring only 20x10x2 mm hence suitable for small RF devices such as remote control key fobs and RF tags.
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Type Approval | |
|
TX Power
|
RX Sensitivity | |||||
| TX3S-868-64 | 869.85 | 2.2 to 4 | 40 |
+4
|
- | EN 300 220-3 |
| TX3A-869-64 | 869.85 | 2.2 to 16 | 64 |
+0
|
- | EN 300 220-3 |
| TX3A-914-64 | 914.5 | 2.2 to 16 | 64 |
+0
|
- | Note 1 |
| TX3B-869-64 | 869.85 | 2.9 to 16 | 64 | +7 | - | EN 300 220-3 |
| TX3B-868-64 | 868.30 | 2.9 to 16 | 64 | +9 | - | EN 300 220-3 |
| TX3H-869.50-10 | 869.50 | 5.0 | 10 | +27 | - | EN 300 220-3 |
| RX3A-868-10 | 868.30 | 2.7 to 16 | 10 | - | -100 | EN 300 220-3 |
| RX3A-868-64 | 868.30 | 2.7 to 16 | 64 | - | -105 | EN 300 220-3 |
| RX3A-869.50-10 | 869.50 | 2.7 to 16 | 10 | - | -100 | EN 300 220-3 |
| RX3A-869-10 | 869.85 | 2.7 to 16 | 10 | - | -107 | EN 300 220-3 |
| RX3A-869-64 | 869.85 | 2.7 to 16 | 64 | - | -100 | EN 300 220-3 |
| RX3G-869-15 | 869.85 | 5.0 | 15 | - | -108 | EN 300 220-3 |
| RX3G-869-64 | 869.85 | 5.0 | 64 | - | -102 | EN 300 220-3 |
| RX3A-914-10 | 914.5 | 2.7 to 16 | 10 | - | -107 | - |
| RX3A-914-64 | 914.5 | 2.7 to 16 | 64 | - | -100 | - |
UHF Wide Band Transceiver
First generation BiM and second generation BiM2 and BiM3A are Bi-directional Modules (tranceivers). These modules integrate a low power UHF FM transmitter and matching superhet receiver.( BiM2 , BiM3A datasheet).
The new BiM2A is an enhanced replacement for the SAW based BiM2 and has better frequency accuracy and temperature stability.
The BiM3B is an enhanced higher power replacement for the European version BiM3A-869-64. (BiM3B datasheet).
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Type Approval | |
| TX Power | RX Sensitivity | |||||
| BiM-418-40 | 418 | 4.5 to 5.5 | 40 | 0 | -100 | Note 3 |
| BiM-433-40 | 433.92 | 4.5 to 5.5 | 40 | 0 | -100 | Note 3 |
| BiM-433-40-HP | 433.92 | 4.5 to 5.5 | 40 | +6 | -100 | Note 3 |
| BiM2-433-64-5V | 433.92 | 5.0 | 64 | +10 | -93 | EN 300 220-3 |
| BiM2-433-64-3V | 433.92 | 3.3 | 64 | +6 | -88 | EN 300 220-3 |
| BiM2-433-64-S* | 433.92 | 5.0 | 64 | +10 | -93 | EN 300 220-3 |
| BiM2-433-160-5V | 433.92 | 5.0 | 64 | +10 | -90 | EN 300 220-3 |
| BiM2-433-160-3V | 433.92 | 3.3 | 64 | +6 | -88 | EN 300 220-3 |
| BiM2A-433-10 | 433.92 | 2.9 to 16 | 10 | +10 | -105 | EN 300 220-3 |
| BiM2A-433-64 | 433.92 | 2.9 to 16 | 64 | +10 | -100 | EN 300 220-3 |
| BiM2A-434-10 | 434.42 | 2.9 to 16 | 10 | +10 | -105 | EN 300 220-3 |
| BiM2A-434-64 | 434.42 | 2.9 to 16 | 64 | +10 | -100 | EN 300 220-3 |
| BiM2A-433-64-3V-CD | 433.92 | 2.9 to 16 | 10 | +10 | -105 | EN 300 220-3 |
| BiM2A-433-64-5V-CD | 433.92 | 2.9 to 16 | 64 | +10 | -100 | EN 300 220-3 |
| BIM3B-869-10 | 869.85 | 2.9 to 16 | 10 | +7 | -105 | EN 300 220-3 |
| BIM3B-869-64 | 869.85 | 2.9 to 16 | 10 | +7 | -100 | EN 300 220-3 |
| BIM3B-868-10 | 868.3 | 2.9 to 16 | 10 | +14 | -105 | EN 300 220-3 |
| BIM3B-868-64 | 868.3 | 2.9 to 16 | 10 | +14 | -100 | EN 300 220-3 |
| BIM3A-869-10 | 869.85 | 2.7 to 6.0 | 10 | +2.5 | -107 | EN 300 220-3 |
| BIM3A-869-64 | 869.85 | 2.7 to 6.0 | 64 | +2.5 | -100 | EN 300 220-3 |
| BIM3A-914-10 | 914.5 | 2.7 to 6.0 | 10 | -1 | -105 | Note 1 |
| BIM3A-914-64 | 914.5 | 2.7 to 6.0 | 64 | -1 | -100 | Note 1 |
* This is intended for RPC or Manchester code only and has fast settling time (<1ms)
Radio Packet Controller
The RPC, RPC2A, FRPC2, RPC3A/B and SP2 are intelligent transceiver modules, which enables a radio network/link to be simply implemented between a number of digital devices. They are self-contained modules, which integrates the BiM/BiM2 and BiM3A/BIM3B transceiver with a microcontroller (RPC-000-SO IC / FRPC-000-SO IC).
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
|
| TX Power | RX Sensitivity | ||||
| RPC-418-40 | 418 | 5.0 | 40 | 0 | -100 |
| RPC-433-40 | 433.92 | 5.0 | 40 | +6 | -100 |
| RPC2A-433-64 | 433.92 | 5.0 | 64 | +10 | -101 |
| FRPC2-433-160 | 433.92 | 5.0 | 160 | +10 | -90 |
| SP2-433-64-5V | 433.92 | 5.0 | 64 | +10 | -95 |
| SP2-433-160-5V | 433.92 | 5.0 | 160 | +10 | -90 |
| RPC3B-869-64 | 869.85 | 5.0 | 64 | +7 | -101 |
| RPC3-914-64 | 914.5 | 5.0 | 64 | +1 | -95 |
Radio Packet Modem
The VHF Radio Packet Modem (RPM1), UHF Radio Packet Modem (RPM3) and UHF SpacePort Modem (SPM2) are low cost highly integrated intelligent serial modems which enable a radio network/link to be simply implemented between a number of digital devices. The RPM1, RPM3 and SPM2 use addressable data packets with error checking, packet acknowledgements and retransmissions to achieve a reliable invisible wireless data link. Built for ease of use and rapid installation, the serial interface ensures direct connection to microprocessors or to RS232 port via RS232 driver while remote configuration enables post installation setup of the modem. (RPM1, RPM2A, RPM3, SPM2 datasheet)
| Module |
Frequency
(MHz) |
Supply
(Volts) |
Throughput
(kbit/s) |
Performance |
|
|
TX Power
|
RX Sensitivity
|
||||
| RPM1-173.250-3 |
173.250
|
5.0
|
3.7
|
+10
|
-115
|
| RPM1-173.250-3-3V |
173.250
|
3.3
|
3.7
|
+10
|
-115
|
| RPM1-173.250-3-HP |
173.250
|
5.0
|
3.7
|
+20
|
-115
|
| RPM1-151.300-3 |
151.300
|
5.0
|
3.7
|
+20
|
-115
|
| RPM1-151.300-3-LP |
151.300
|
5.0
|
3.7
|
+10
|
-115
|
| RPM1-151.300-3-LP-3V |
151.300
|
3.3
|
3.7
|
+10
|
-115
|
| RPM2A-433-17 |
433.92
|
5.0
|
17
|
+10
|
-100
|
| RPM2A-433-17-3V |
433.92
|
3.0
|
17
|
+10
|
-100
|
| RPM2A-433-17-SMA |
433.92
|
5.0
|
17
|
+10
|
-100
|
| RPM2A-433-17-3V-SMA |
433.92
|
3.0
|
17
|
+10
|
-100
|
| RPM2A-433-17-ANT |
433.92
|
5.0
|
17
|
+10
|
-100
|
| RPM2A-433-17-3V-ANT |
433.92
|
3.0
|
17
|
+10
|
-100
|
| RPM3B-869-17 |
869.85
|
5.0
|
17
|
+7
|
-100
|
| RPM3B-868-17 |
868.3
|
5.0
|
17
|
+14
|
-100
|
| RPM3-914-17 |
914.50
|
5.0
|
17
|
+1
|
-100
|
| RPM3B-869-17-3V |
869.85
|
5.0
|
17
|
+7
|
-100
|
| RPM3B-868-17-3V |
868.3
|
5.0
|
17
|
+14
|
-100
|
| RPM3-914-17-3V |
914.50
|
5.0
|
17
|
+1
|
-100
|
| RPM3B-869-17-SMA |
869.85
|
5.0
|
17
|
+7
|
-100
|
| RPM3B-868-17-SMA |
868.3
|
5.0
|
17
|
+14
|
-100
|
| RPM3-914-17-RPS |
914.50
|
5.0
|
17
|
+1
|
-100
|
| RPM3B-869-17-3V-SMA |
869.85
|
3.0
|
17
|
+7
|
-100
|
| RPM3B-868-17-3V-SMA |
868.3
|
3.0
|
17
|
+14
|
-100
|
| RPM3-914-17-3V-RPS |
914.50
|
5.0
|
17
|
+1
|
-100
|
| RPM3B-869-17-ANT |
869.85
|
5.0
|
17
|
+7
|
-100
|
| RPM3B-868-17-ANT |
868.3
|
5.0
|
17
|
+14
|
-100
|
| RPM3-914-17-ANT |
914.50
|
3.0
|
17
|
+1
|
-100
|
| RPM3B-869-17-3V-ANT |
869.85
|
5.0
|
17
|
+7
|
-100
|
| RPM3B-868-17-3V-ANT |
868.3
|
5.0
|
17
|
+14
|
-100
|
| RPM3-914-17-3V-ANT |
914.50
|
3.0
|
17
|
+1
|
-100
|
| SPM2-433-18 |
433.92MHz
|
5.0
|
18
|
+10
|
-95
|
|
SPM2-433-18-3V
|
433.92MHz
|
3.3
|
18
|
+6
|
-90
|
| SPM2-433-28 |
433.92MHz
|
5.0
|
28
|
+10
|
-90
|
RPS: with RPSMA connector; ANT: with RPSMA connector and RPSMA antenna
UHF Multi Channel Transparent Data Link Transceiver
The TDL2A and TDH2 are 9600baud half-duplex multi channel OEM radio modems in BiM2 footprint, operating on European and Australian 433MHz ISM band. Both acts as a transparent serial cable to attached host. The TDi2 RS232 interface board enables a cable free transparent data link between RS232 ports without any additional interface circuitry. (TDL2A, TDH2, TDi2, TDM2 datasheet
| Module |
Frequency
(MHz) |
Supply
(Volts) |
Buad rate
(bit/s) |
Performance |
|
|
TX Power
|
RX Sensitivity
|
||||
| TDL2A-433-9 |
433.285 - 434.565
|
5.0
|
9600
|
+10
|
-107
|
| TDL2A-433-4 |
433.285 - 434.565
|
5.0
|
4800
|
+10
|
-107
|
| TDL2A-433-2 |
433.285 - 434.565
|
5.0
|
2400
|
+10
|
-107
|
| TDH2-433-9 |
433.285 - 434.565
|
5.0
|
9600
|
+14
|
-107
|
| TDH2-433-4 |
433.285 - 434.565
|
5.0
|
4800
|
+14
|
-107
|
| TDH2-433-2 |
433.285 - 434.565
|
5.0
|
2400
|
+14
|
-107
|
| TDL2T-433-9 |
433.285 - 434.565
|
5.0
|
9600
|
+10
|
-
|
| TDH2T-433-9 |
433.285 - 434.565
|
5.0
|
9600
|
+14
|
-
|
| TDL2R-433-9 |
433.285 - 434.565
|
5.0
|
9600
|
-
|
-107
|
| TDi2-433-9 |
433.285 - 434.565
|
7.0 to 15.0
|
9600
|
+10
|
-107
|
| TDi2-433-4 |
433.285 - 434.565
|
7.0 to 15.0
|
4800
|
+10
|
-107
|
| TDi2-433-2 |
433.285 - 434.565
|
7.0 to 15.0
|
2400
|
+10
|
-107
|
| TDM2-433-4 |
433.285 - 434.565
|
7.0 to 15.0
|
9600
|
+10
|
-107
|
| TXL2-433-9 |
433.285 - 434.565
|
5.0
|
9600
|
+10
|
-
|
| RXL2-433-9 |
433.285 - 434.565
|
5.0
|
9600
|
-
|
-107
|
| TXL2-433-4 |
433.285 - 434.565
|
5.0
|
4800
|
+10
|
-
|
| RXL2-433-4 |
433.285 - 434.565
|
5.0
|
4800
|
-
|
-107
|
9600 baud serial RF Modem IC
The i9600 is a 9600baud half-duplex serial modem controller suitable for use with wideband receivers, transmitters and transceivers. It takes care of preamble, synchronisation, bit balancing and error checking and enables a transparent radio data link to be established between radio devices.
| Part number | Package |
| i9600-000-SS | Shrink Small Outline |
| i9600-000-SO | Small Outline |
| i9600-000-DIL | Plastic Dual In Package |
*The i9600 modem ICs cannot be ordered separately. They should be ordered with equal number of Radiometrix radio modules.
Narrow band Eval Kit controller IC
The NBEK controller IC which features an i1200 modem function, can also be ordered separately with equal number of radio modules. The i1200 is 1200baud half-duplex serial modem suitable for use with narrow band receivers, transmitters and transceivers.
| Part number | Package |
| NBEK-000-SS | Shrink Small Outline |
| NBEK-000-SO | Small Outline |
| NBEK-000-DIL | Plastic Dual In Package |
VHF Narrow Band FM multi channel radio modules with built-in modem
The RX1M receiver, TX1M transmitter and SMX1 transceiver modules offer a low power, reliable data link in an industry-standard pin out and footprint. TX1M/RX1M are available in any 2MHz band from 135-175MHz. The RF power output of TX1M can be factory set from 10mW up to 200mW. The SMX1 transceiver is in any 2MHz band from 130 - 180MHz with up to 50mW RF power output.
(TX1M/RX1M, and SMX1 transceiver data sheet)
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Notes
|
|
| TX Power | RX Sensitivity | |||||
| TX1M-xxx-5 |
*135-175
|
4.5 to 15
|
5
|
+10 to +23
|
-
|
Non-inverted |
| TX1I-xxx-5 |
*135-175
|
4.5 to 15
|
5
|
+10 to +23
|
-
|
Inverted |
| TX1M-xxx-10 |
*135-175
|
4.5 to 15
|
10
|
+10 to +23
|
-
|
Non-inverted |
| TX1I-xxx-10 |
*135-175
|
4.5 to 15
|
10
|
+10 to +23
|
-
|
Inverted |
| RX1M-xxx-5 |
*130-180
|
4.5 to 15
|
5
|
-
|
-118
|
|
| RX1M-xxx-10 |
*130-180
|
4.5 to 15
|
10
|
-
|
-118
|
|
| SMX1-151-5 |
150.825 - 152.45
|
4.2 to 15
|
5
|
+0 to +17
|
-118
|
|
| SMX1-173-5 |
173.200 - 173.325
|
4.2 to 15
|
5
|
+0 to +17
|
-118
|
|
| TR1M-xxx-5 |
*135 - 175
|
4.5 to 15
|
5
|
+10 to +20
|
-118
|
|
| UHX1-144-5 |
144 - 146
|
5
|
5
|
+0 to +27
|
-118
|
|
| UHX1-169-5 |
169 - 171
|
5
|
5
|
+0 to +27
|
-118
|
|
*Where xxx is any 3MHz band from 135-175MHz for TX1M and any 2MHz band from 130-180MHz for RX1M and TR1M.
VHF Low cost Narrow Band FM multi channel radio modules
The LMT1 and LMR1 are low cost multi channel transmitter/receivers with up to 32 parallel and serial select channels. ( LMT1/LMR1 data sheet).
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Notes
|
|
| TX Power | RX Sensitivity | |||||
| LMT1-151-10 |
150.825 - 152.450
|
3.1 - 15
|
10
|
+10
|
-
|
|
| LMT1-151-10 |
150.825 - 152.450
|
4.1 - 15
|
10
|
+20
|
-
|
|
| LMR1-151-5 |
150.825 - 152.450
|
3.1 - 15
|
5
|
-
|
-118
|
|
| LMR1-151-10 |
150.825 - 152.450
|
3.1 - 15
|
10
|
-
|
-118
|
|
|
-
|
||||||
| LMT1-173-10 |
173.200 - 173.325
|
3.1 - 15
|
5
|
+10
|
-
|
|
| LMR1-173-5 |
173.200 - 173.325
|
3.1 - 15
|
5
|
-
|
-118
|
|
| LMR1-173-10 |
173.200 - 173.325
|
3.1 - 15
|
5
|
-
|
-118
|
|
| LMT1-151-5-12k5 |
150.825 - 152.450
|
3.1 - 15
|
5
|
+10
|
-
|
|
| LMT1-151-5-12k5 |
150.825 - 152.450
|
4.1 - 15
|
5
|
+20
|
-
|
|
|
LMR1-151-5-12k5 |
150.825 - 152.450
|
3.1 - 15
|
5
|
-
|
-118
|
|
| LMT1-173-5-12k5 |
173.200 - 173.325
|
3.1 - 15
|
5
|
+10
|
-118-
|
|
| LMR1-173-5-12k5 |
173.200 - 173.325
|
3.1 - 15
|
5
|
-
|
-118
|
|
Note: Other custom variants from 130 - 180MHz on any 2MHz band
UHF Narrow Band FM multi channel radio modules with built-in modem
The RX2M receiver, TX2M transmitter, TR2M ans SMX2 transceiver modules offer a low power, reliable data link in an industry-standard pin out and footprint. Two versions are available, covering the 458.5-458.8MHz UK band (at 100mW) and the European 433.05-434.79MHz band.
(TX2M/RX2M, TR2M transceiver and SMX2 transceiver data sheet)
USX2 is small multi-channel half duplex UHF transceiver available for operation on 315MHz, 433MHz and 458MHz bands with the user programmable RF power output of up to 100mW.
The LSR2 is a low current multichannel design in an RX2M footprint/pinout. It is similar in performance to a LMR2 receiver but only draws 10mA at 3.1 -15V.
RMX2 is a narrowband multichannel module with 25 kHz channel steps, but still achieves sub-10mS TX/RX switching speed, making it an ideal RF unit for inclusion in feedback systems.
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Notes
|
|
| TX Power | RX Sensitivity | |||||
| TX2M-458-5 |
458.5 - 459.1
|
4.5 to 15
|
5
|
+20
|
-
|
Non-inverted |
| TX2M-433-5 |
433.05 - 434.79
|
4.5 to 15
|
5
|
+10
|
-
|
Non-inverted |
| RX2M-458-5 |
458.5 - 459.1
|
4.5 to 15
|
5
|
-
|
-118
|
|
| RX2M-433-5 |
433.05 - 434.79
|
4.5 to 15
|
5
|
-
|
-118
|
|
| TX2I-458-5 |
458.5 - 459.1
|
4.5 to 15
|
5
|
+20
|
-
|
Inverted |
| TX2I-433-5 |
433.05 - 434.79
|
4.5 to 15
|
5
|
+10
|
-
|
Inverted |
| TX2M-458-10 | 458.5 - 459.1 | 4.5 to 15 |
10
|
+20
|
-
|
Non-inverted
|
| TX2I-458-10 | 458.5 - 459.1 | 4.5 to 15 |
10
|
+20
|
-
|
Inverted
|
| RX2M-458-10 | 458.5 - 459.1 | 4.5 to 15 |
10
|
-
|
-118
|
|
| TR2M-433-5 | 433.05 - 434.79 | 4.5 to 15 |
5
|
+10
|
-118
|
|
| TR2I-433-5 | 433.05 - 434.79 | 4.5 to 15 |
5
|
+10
|
-118
|
Inverted TX/RX |
| TR2M-458-5 | 458.5 - 459.1 | 4.5 to 15 |
5
|
+20
|
-118
|
|
| TR2I-458-5 | 458.5 - 459.1 | 4.5 to 15 |
5
|
+20
|
-118
|
Inverted TX/RX |
| TR2M-458-10 | 458.5 - 459.1 | 4.5 to 15 |
10
|
+20
|
-118
|
|
| TR2I-458-10 | 458.5 - 459.1 | 4.5 to 15 |
10
|
+20
|
-118
|
Inverted TX/RX |
| SMX2-433-5 | 433.05 - 434.79 |
4.2 - 15
|
5
|
+10
|
-118
|
|
| USX2-315-5 | 315 - 315.75 |
3.1 - 15
|
5
|
-10 to +20
|
-118
|
|
| USX2-433-5 | 433.05 - 434.79 |
3.1 - 15
|
5
|
-10 to +20
|
-118
|
|
| USX2-458-5 | 458.5 - 459.1 |
3.2 - 15
|
5
|
-10 to +20
|
-118
|
|
| RMX2-433-10 | 433.05 - 434.79 |
3.0 - 15
|
10
|
+10
|
-118
|
|
| RMX2-458-10 | 458.5 - 459.1 |
3.0 - 15
|
10
|
+10
|
-118
|
|
| BHX2-458-5 | 458.5 - 459.1 | 5.5 to 15 |
5
|
+27
|
-118
|
Inverted TX/RX |
Low cost Narrow Band FM multi channel radio modules
The TLC2H and RLC2H are lo cost multi channel transmitter/receivers with industry standard pinout and foot print. They have up to 32 parallel and serial select channel. LMT2 and LMR2 are enhanced performance transmitter and receivers in Radiometrix pin out.
The HVR2 receiver is the high vibration resistant version of the RLC2 receiver. It is immune to mechanical vibration below 500Hz, hence suitable for mechanically troublesome application. E.g. Crane control
(TLC2H/RLC2H - HVR2 - LMT2/LMR2 data sheet)
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Notes
|
|
| TX Power | RX Sensitivity | |||||
| TLC2H-433-5 |
433.875-434.650
|
3.1 - 15.0
|
5
|
+10
|
-
|
|
| RLC2H-433-5 |
433.875-434.650
|
3.7 - 15.0
|
5
|
-
|
-118
|
|
| LMT2-433-5 |
433.900-434.650
|
3.1 - 15.0
|
5
|
+10
|
-
|
|
| LMR2-433-5 |
433.900-434.650
|
3.1 - 15.0
|
5
|
-
|
-18
|
|
| LMT2-433-10 |
433.900-434.650
|
3.1 - 15.0
|
5
|
+10
|
-
|
|
| LMR2-433-10 |
433.900-434.650
|
3.1 - 15.0
|
5
|
-
|
-18
|
|
| LMT2-458-5 |
458.5 - 459.1
|
3.1 - 15.0
|
5
|
+10
|
-
|
|
| LMR2-458-5 |
458.5 - 459.1
|
3.1 - 15.0
|
5
|
-
|
-18
|
|
| LMT2-458-10 |
458.5 - 459.1
|
3.1 - 15.0
|
10
|
+10
|
-
|
|
| LMR2-458-10 |
458.5 - 459.1
|
3.1 - 15.0
|
10
|
-
|
-18
|
|
| LMT2-458-5 |
458.5 - 459.1
|
4.1 - 15.0
|
10
|
+10
|
-
|
|
| HVR2-433-5 |
433.875-434.650
|
3.7 - 15.0
|
5
|
-
|
-118
|
|
RF remote control Encoder/decoder
The KFX2 is a UHF code hopping 5 button keyfob transmitter where as the KTX2 is an OEM version intended for PCB mounting and both are suitable for use with the matching KDEC decoder or KRX-416-000-DIL decoder IC to provide a secure remote controlled link in excess of 100 metres over open ground.
| Module | Frequency (MHz) | Supply (V) |
| KTX2-433 | 433.92 | 3.0 - 6.0 |
| KFX2-433 | 433.92 | 6.0 |
| KDEC-433-000 | 433.92 | 7.0 - 15 |
| *KDEC-433-00n | 433.92 | 7.0 - 15 |
· * "n" is a number between 1 and 5. This version is optimised for use with KFX (Key-fob transmitter with 1 - 5 buttons fitted). Only one output at a time may be activated.
· Where "xxx" is frequency band in MHz - 433 is standard. Please contact sales for other requirements
RF remote control Encoder/decoder IC
Control44 is a 4 bit address, 4 bit data encoder and decoder where as Control124 is 12 bits data and 4 bit address encoder/decoder combined in a single IC. Both devices device can be operated in either Encode or Decode mode. They use 1kbps bi-phase communication protocol with preamble, which is specifically designed to be used in RF remote control applications. CTA88 is an 8 bit address, 8 bit data encoder and decoder combined in a single IC.
Key-code Receiver KRX416 is a single IC solution for decrypting and decoding Radiometrix code-hopping transmitters like KFX2 and KTX2-433.
| Module | Description | Package |
| CTR44-000-SS | Standard Control44 (£4MHz) | Shrink Small Outline |
| CTR44-000-SO | Standard Control44 (£4MHz) | Small Outline |
| CTR44-000-DIL | Standard Control44 (£4MHz) | Plastic Dual In Package |
| CTR44L-000-SS | Low Voltage (£4MHz) | Shrink Small Outline |
| CTR44L-000-SO | Low Voltage (£4MHz) | Small Outline |
| CTR44L-000-DIL | Low Voltage (£4MHz) | Plastic Dual In Package |
| CTR44H-000-SS | High Speed (4 - 20MHz) | Shrink Small Outline |
| CTR44H-000-SO | High Speed (4 - 20MHz) | Small Outline |
| CTR44H-000-DIL | High Speed (4 - 20MHz) | Plastic Dual In Package |
| CTA88-000-SS | Standard Control44 (£4MHz) | Shrink Small Outline |
| CTA88-000-SO | Standard Control44 (£4MHz) | Small Outline |
| CTA88-000-DIL | Standard Control44 (£4MHz) | Plastic Dual In Package |
| CTA88L-000-SS | Low Voltage (£4MHz) | Shrink Small Outline |
| CTA88L-000-SO | Low Voltage (£4MHz) | Small Outline |
| CTA88L-000-DIL | Low Voltage (£4MHz) | Plastic Dual In Package |
| CTA88H-000-SS | High Speed (4 - 20MHz) | Shrink Small Outline |
| CTA88H-000-SO | High Speed (4 - 20MHz) | Small Outline |
| CTA88H-000-DIL | High Speed (4 - 20MHz) | Plastic Dual In Package |
| CTR124-000-SS | Standard Control44 (£4MHz) | Shrink Small Outline |
| CTR124-000-SO | Standard Control44 (£4MHz) | Small Outline |
| CTR124-000-DIL | Standard Control44 (£4MHz) | Plastic Dual In Package |
| CTR124L-000-SS | Low Voltage (£4MHz) | Shrink Small Outline |
| CTR124L-000-SO | Low Voltage (£4MHz) | Small Outline |
| CTR124L-000-DIL | Low Voltage (£4MHz) | Plastic Dual In Package |
| CTR124H-000-SS | High Speed (4 - 20MHz) | Shrink Small Outline |
| CTR124H-000-SO | High Speed (4 - 20MHz) | Small Outline |
| CTR124H-000-DIL | High Speed (4 - 20MHz) | Plastic Dual In Package |
| KRX416-000-SS | Key-code Decoder | Shrink Small Outline |
| KRX416-000-SO | Key-code Decoder | Small Outline |
| KRX416-000-DIL | Key-code Decoder | Plastic Dual In Package |
Evaluation Kits
TDL2A Evaluation Kit
SpacePort Evaluation Kit
SpacePort Modem Evaluation Kit
Universal Evaluation Kit
Control44 Encoder/decoder Evaluation kit
Narrow band Eval Kit (NBEK)
First generation radio modules*
*Not recommended for new designs. These modules will remain in production for existing customers.
| Module | Frequency (MHz) |
Supply (Volts) |
Data rate (kbit/s) |
Performance |
Type Approval | |
| TX Power | RX Sensitivity | |||||
| TXM-418-5 | 418 | 6.0 to 9.0 | 5 |
0
|
- | Note 3 |
| TXM-418-10 | 418 | 2.7 to 4.0 | 10 |
0
|
- | Note 3 |
| TXM-433-5 | 433.92 | 6.0 to 9.0 | 5 |
0
|
- | EN 300 220-3 |
| TXM-433-10 | 433.92 | 2.7 to 4.0 | 10 |
0
|
- | EN 300 220-3 |
| SILRX-418-5 | 418 | 4.0 to 9.0 | 5 | - | -107 | N/A |
| SILRX-418-10 | 418 | 4.0 to 9.0 | 10 | - | -100 | N/A |
| SILRX-433-5 | 433.92 | 4.0 to 9.0 | 5 | - | -107 | N/A |
| SILRX-433-10 | 433.92 | 4.0 to 9.0 | 10 | - | -100 | N/A |
| RXM-418-10 | 418 | 4.5 to 5.5 | 10 | - | -107 | N/A |
| RXM-433-10 | 433.92 | 4.5 to 5.5 | 10 | - | -107 | N/A |
TXM - UHF FM transmitter module
SILRX - Single In Line (SIL) UHF FM receiver module
RXM - UHF FM receiver module with RSSI, Jamming Signal Detector, Antenna Tamper Sensing
Notes: 1. The finished product incorporating these modules must be approved by the FCC.
2. Test report will be available soon.
3. The finished product incorporating these modules may require approval from the Radio Authority of the respective country.
Limitation of Liability
The information furnished by Radiometrix Ltd. is believed to be accurate and reliable. Radiometrix reserves the right to make changes or improvements in the design, specification or manufacture of its subassembly products without notice. Radiometrix does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the use of its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular application. These radio devices may be subject to radio interference and may not function as intended if interference is present. We do NOT recommend their use for life critical applications.
Radio and EMC Regulations
The Intrastat commodity code for all our modules is : 8542 6000. The purchaser of Radiometrix sub-assemblies must satisfy all relevant EMC and radio regulations which applies to their finished products. Information regarding EMC regulations and type approval please refer to following URLs
USA : www.fcc.gov
Europe www.ero.dk
UK :: www.ofcom.org.uk
